6/12 V - 6/25 V

All movements are hydraulic

All the machine's movements are controlled by a high-efficiency motor pump unit located in the oil tank and easily inspected.

Pneumatic safety gate

Pneumatic drive for opening and closing the mould protection gate (Standard and “V” Table versions).

Standard machine plans

The machine's design allows for quick and easy assembly. In some cases, with minor modifications, existing molds can be used.

Movements

The press is governed by two microprocessors that monitor and manage the movements, times and temperatures of the production cycle.

Proportional Hydraulics

Thanks to proportional hydraulics, the pressures during the cycle phases are managed and stored by the

machine.

Maximum security

CE certification.

Mold safety

Approaching in low pressure.

Color Touch Screen Display

USB output and Ethernet connection (Modbus TCP)

Cooling Management

The flow rate of the coolant at various points in the press, including the mold, can be adjusted using a flow meter. For mold temperatures up to 90°C, a specific Babyplast thermoregulator is available (only 0.7 kW).

Heating the mold or hot chamber

For mold temperatures up to 200°C, the machine has two 230V heating zones for the mold or hot runner. To condition the mold, you can insert cartridge heaters and control their heating in % or °C (using thermocouples), or you can use a nozzle or hot runner, managing their heating directly from the machine.

Injection possible in three different positions

The injection group, positioned horizontally, has three injection positions (45mm, 70mm and 95mm) with respect to the lower machine plane.

Closure without columns

8″ backlit LCD touch screen display

10 different languages selectable

Pages can be easily consulted thanks to the multifunction keys

Quality control on 4 cycle parameters

PID temperature control (up to 420°C)

5 temperature control zones, two of which are free for regulating the mould temperature or 230V hot runner

Manages and stores 100 production cycles

USB output program backup

Ethernet connection: Modbus TCP

Pressure control with electronic transducer
Injection position and closure control with linear transducers

Proportional hydraulics

Soundproofed motor pump unit controlled by inverter

Euromap 67 card (option)

3 different configurations: standard, rotary table, “V” table

Low running costs – installed power 3kW – cooling approximately 120 l/h

3 different injection positions

2 injection groups: Standard (max 15cc) – Plus (max 36cc) with 5 injection pistons

Output for auxiliary control

Cooling circuit (6 zones)

Temperature tolerance band

Hydraulic extraction with extractor return control sensor

Jack management and air blowing

Advantages

Quality of the pieces produced

Low-cavity mold. Dimensional accuracy is easy to achieve. Thanks to the low hourly cost, competitive pricing is possible even with molds with just a few cavities.
Simple balancing cavity layout.
Uniform mold temperature. Thanks to the small mold size and the positioning of thermocouples (both fixed and mobile) near the cavities.
Air-conditioned injection unit. Thanks to its compact size, the material present in the injection unit after mixing is only a few cubic centimeters, and the injection unit, including the nozzle, is cooled. This ensures the integrity of the material even for very small weights.

Low production cost

Low power consumption. Only 3 kW of installed power, inverter for motor speed management. In cycle, it consumes only 1.5 to 2.5 kW.
Reduced mold and material changeover times. Mold centered with the aid of two pins on the fixed plate and secured with two screws on each side of the machine plate. Material and color change in approximately 150g.
Low consumption for mold heating. Reduced mold size, resulting in less time and energy needed to reach and maintain the correct mold temperature. Use of two cartridge heaters and a thermocouple for each mold half. Mold temperature control directly from the machine.
Compact footprint. Less than 1m² (0.6m x 1m).
Modularity in mixing systems. Three different LSR mixing and loading systems are available: a 0.5 kg pre-mixed cartridge, a dispenser with a two-component mixer for 1 kg cartridges (A+B), and a dispenser with a two-component mixer for 20 kg containers. This allows us to meet requirements ranging from prototyping to large-scale production, while minimizing investment.

Low investment in the mold

Low-cavity molds. Thanks to the machine's low hourly cost (approximately €2 to €2.5/h), low production costs are possible even with low-cavity molds. Especially for technical items where cavity costs are high (use of slides, etc.), the savings in reducing the number of cavities leads to significant cost reductions.
Direct injection machine nozzle. Thanks to a special cooled machine nozzle with a pneumatic needle valve, direct injection from the machine to the workpiece is possible.